Your industrial partner

Protection against dust

Protection against dust explosive

You can use various types of protection to meet the ATEX Directive EHSR depending on the area where the equipment is installed .
The purpose of protection is to prevent the engine from becoming a possible explosive source .

The technical solution depends EHSR of ATEX Directive according to the category of the equipment.

Protection type ” D “, ” dip ” or ” Ex td ” prevent : 


presence of explosive dust atmosphere

Type of protectionProtection based Protection Type
Dust ignition proof / td Ex – IP 55
  • Explosive dust can not penetrate in sufficient quantity as to interfere with the active part of the motor inside the engine protected ..
  • Absence of high temperature surfaces and dangerous sparks on the outside of the casing in nominal operating conditions .
Resistant to dust ignition / td Ex –
IP 65
  • IP 65 explosive dust can not penetrate inside the motor impervious to dust.
    Absence of dangerous surfaces at high temperatures and sparks on the outside of the casing at nominal operating conditions and under certain conditions of failure.

temperature class

The brand temperature corresponds to the temperature of the engine class . In the case of engine ignition protected against dust , this temperature corresponds to the maximum temperature of the outer surface of the product.
Users must follow different rules depending on the gaseous environment to install a motor in an explosive atmosphere .
The limits described in the following table should be followed in all cases in accordance with the ATEX Directive and IEC standards :

Brand engine temperatureTemperature Environment dust ignitionMinimum ignition temperature of potentially explosive atmosphere
T °C (125°C)CloudT°cloudT°cloud > 3/2 x T°C (190°C)
Layer up to  5 mm (gruix del motor)T°5mmT°5mm > T°C + 75 K (200°C)

Protection against dust explosive

You can use various types of protection to meet the ATEX Directive EHSR depending on the area where the equipment is installed .
The purpose of protection is to prevent the engine from becoming a possible explosive source .
The technical solution depends EHSR of ATEX Directive according to the category of the equipment.

Protection type ” D “, ” dip ” or ” Ex td ” prevent :

presence of explosive dust atmosphere
Protection based Protection Type
Dust ignition proof / td Ex – IP 55
Explosive dust can not penetrate in sufficient quantity as to interfere with the active part of the motor inside the engine protected ..
Absence of high temperature surfaces and dangerous sparks on the outside of the casing in nominal operating conditions .

Resistant to dust ignition / td Ex –
IP 65
IP 65 explosive dust can not penetrate inside the motor impervious to dust.
Absence of dangerous surfaces at high temperatures and sparks on the outside of the casing at nominal operating conditions and under certain conditions of failure.

temperature class

The brand temperature corresponds to the temperature of the engine class . In the case of engine ignition protected against dust , this temperature corresponds to the maximum temperature of the outer surface of the product.
Users must follow different rules depending on the gaseous environment to install a motor in an explosive atmosphere .
The limits described in the following table should be followed in all cases in accordance with the ATEX Directive and IEC standards :

Brand engine temperature Temperature Environment dust ignition Minimum ignition temperature of potentially explosive atmosphere
T ° C ( 125 ° C ) Cloud Cloud T ° T ° Cloud > 3/2 x T ° C ( 190 ° C )

Layer up to 5 mm (thickness engine ) T ° ° 5mm 5mm T > T C + 75 ° K (200 ° C )

With a higher layer of 5 mm, special requirements are needed . Please check with the manufacturer .

Standards affected by protection ” DIP / Ex td ” :
EN 61241-1 : 2004-06 Electrical apparatus for use in presence of combustible dust . Part 1 : Protection by enclosure ” td ” according to IEC 61261-1 

EN 50281-1-1:1998 Electrical equipment for use in presence of combustible dust . Part 1-1 : Electrical equipment protected by shells – Construction and testing .

EN 50281-1-2:1998 Electrical equipment for use in presence of combustible dust . Part 1-2 : Electrical apparatus protected by shells – Selection , installation and maintenance

IEC 61241-0 : 2004-07 Electrical apparatus for use in presence of combustible dust . Part 0 : General requirements .

IEC 61241-14 : 2004-07 Electrical apparatus for use in presence of combustible dust . Part 14 : Selection and installation

General characteristics for the design of ABB motors type of protection against ignition of dust.